I-self-drilling system ye-anchor
I-ankile isetyenziswa kakhulu kwitonela yenkxaso yangaphambili, ithambeka, unxweme, umgodi, iiprojekthi zogcino lwamanzi, isiseko sokwakha, ukuqinisa umandlalo wendlela kunye nonyango olungalunganga lwejoloji olufana ne-landslip, i-crack, kunye neminyaka yokutshona, ayinakuphinda ibuyiselwe kwimeko yolwakhiwo olumxinwa.
AMALUNGELO
Inkqubo yeAnchor yeBha yokuZimbela:
Iqulathe umngxunya webha enemisonto edityaniswe nentwana yedrili eyenza ukomba.Ibha enombhobho ivumela umoya kunye namanzi ukuba badlule ngokukhululekileyo kwi-bar ngexesha lokugaya ukususa i-debris, emva kokuba ukubhobhoza kubunzulu obufunekayo kugqityiwe, i-grout igcwalisa ibha engenanto ngoxinzelelo lwemfuno yabo kwaye igubungela ngokupheleleyo i-bolt yonke.
I-Coupler: I-coupler ingasetyenziselwa ukudibanisa imivalo engenanto kunye nokwandisa ubude bebholiti, oko kuthetha ukuba i-ankile inokonyulwa kunye nee-couplers.
Ipleyiti kunye namantongomane: Ipleyiti kunye namantongomane zifakwe ngokwemfuno yazo yoyilo.
I-drill bit: I-drill bit iya kukhethwa ngokukhetha imeko yomhlaba.
R25 Self Drilling Ankile
Ibha yeAnchor eHollow | |||||
Ubungakanani | Dia yangaphandle. | I-Dia yangaphakathi. | Umthwalo wokugqibela | Yield Load | Ubunzima |
(mm) | (mm) | (kN) | (kN) | (Kg/m) | |
R25-12 | 25 | 12 | 200 | 150 | 2.35 |
I-Drill Bit | ||||
Uhlobo | Dia yangaphandle. | Ubunzima | Uluhlu lweSicelo (Iingcebiso) | |
(mm) | (intshi) | (Ikg) | ||
Cast bit cross | 42 | 1.65 | 0.35 | Phosa bits yomnqamlezo kwisanti kunye negrabile |
51 | 2 | 0.38 | ||
Steel cross bit | 42 | 1.65 | 0.3 | Isuntswana lesiphambano esiqinileyo ukuze sikhululeke ukuya kwiimeko ezixineneyo ezinamatye amancinci. |
51 | 2 | 0.4 | ||
TC umnqamlezo bit | 42 | 1.65 | 0.35 | I-TC cross bit yolwakhiwo oluthambileyo ukuya oluphakathi |
51 | 2 | 0.45 |
Umlingane | ||||
Ubungakanani | Dia yangaphandle. | Ubude | Ubunzima | Phawula |
(mm) | (mm) | (Kg/pc) | ||
I-R25-S | 36 | 150 | 0.66 | Ngesakhiwo sokutywina |
R25-E | 36 | 150 | 0.66 | Ngaphandle kwesakhiwo sokutywina |
Hex Nut | ||||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima | Ukuqina |
(mm) | (mm) | (Kg/pc) | (HRC) | |
I-R25-S | 41 | 30 | 0.2 | 25-30 |
Ipleyiti eDomed | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
R25-E | 150×150 | 8 | 30 | 1.4 |
150×150 | 5 | 28 | 0.85 | |
200×200 | 8 | 32 | 3.2 |
R32 Self Drilling Ankile
Ibha yeAnchor eHollow | |||||
Ubungakanani | Dia yangaphandle. | I-Dia yangaphakathi. | Umthwalo wokugqibela | Yield Load | Ubunzima |
(mm) | (mm) | (kN) | (kN) | (Kg/m) | |
S-R32/20 | 32 | 20 | 210 | 160 | 2.83 |
S-R32/17 | 32 | 17 | 280 | 230 | 3.5 |
S-R32/15 | 32 | 15 | 360 | 280 | 4 |
E-R32/21 | 32 | 21 | 210 | 160 | 2.6 |
E-R32/19 | 32 | 19 | 280 | 230 | 2.95 |
E-R32/17 | 32 | 17 | 360 | 280 | 3.5 |
E-R32/15 | 32 | 15 | 405 | 320 | 4 |
C-R32/21 | 32 | 21 | 250 | 190 | 2.6 |
C-R32/20 | 32 | 20 | 280 | 230 | 2.83 |
C-R32/17.5 | 32 | 17.5 | 360 | 280 | 3.4 |
I-Drill Bit | |||
Uhlobo | Dia yangaphandle. | Ubunzima | Uluhlu lweSicelo (Iingcebiso) |
(mm) | (Ikg) | ||
Cast bit cross | 51 mm | 0.99 | Phosa bits yomnqamlezo kwisanti kunye negrabile |
Steel cross bit | 51 mm | 0.88 | Isuntswana lentsimbi eqinileyo yokukhululeka ukuya kwiimeko ezixineneyo zomhlaba |
76 mm | 2.87 | ||
Steel 3 cutter bit | 76 mm | 2.65 | |
TC umnqamlezo bit | 51 mm | 0.99 | I-TC ifake isuntswana kulwakhiwo oluthambileyo ukuya kweliphakathi |
TC 3 cutter bit | 76 mm | 2.87 | |
Steel arched bit | 51 mm | 0.99 | Isuntswana le-arched arched for optimized geometry kumhlaba ongadityaniswanga onamatye amancinci |
TC arched bit | 51 mm | 0.99 | I-TC i-arched bit yejometri ephuculweyo yokwakheka kwamatye athambileyo ukuya aphakathi |
Steel iqhosha bit | 51 mm | 1.32 | Intwana yeqhosha eliqinileyo lelitye elingadityaniswanga elinamatye |
bit iqhosha le-TC | 51 mm | 1.43 | I-TC faka iqhosha elincinci lokwenziwa kwelitye eliphakathi |
EX bit | 51 mm | 0.88 | Umnqamlezo owenziweyo oqinileyo, olungele uninzi lwezicelo ezibandakanya iibhanti ezimxinwa zamatye athambileyo. |
EXX bit(enye) | 51 mm | 1.1 | I-EXX yeyona nto inzima yokubhola ekhoyo, yelitye elomeleleyo, i-hard seams kunye neenyawo zekhonkrithi. |
Umlingane | ||||
Ubungakanani | Dia yangaphandle. | Ubude | Ubunzima | Phawula |
(mm) | (mm) | (Kg/pc) | ||
SSR32 | 42 | 145 | 0.79 | Ngesakhiwo sokutywina |
42 | 160 | 0.86 | ||
42 | 190 | 1 | ||
I-SER32 | 42 | 145 | 0.77 | Ngaphandle kwesakhiwo sokutywina |
42 | 160 | 0.84 | ||
42 | 190 | 1 |
Hex Nut | ||||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima | Ukuqina |
(mm) | (mm) | (Kg/pc) | (HRC) | |
SSR32 | 46 | 45 | 0.37 | 25-30 |
46 | 55 | 0.46 | ||
46 | 60 | 0.47 |
Ipleyiti eDomed | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
R32-E | 150×150 | 8 | 35 | 1.3 |
150×150 | 5 | 35 | 0.85 | |
150×150 | 6 | 35 | 1 | |
150×150 | 10 | 35 | 1.7 | |
175×175 | 8 | 35 | 1.9 | |
200×200 | 8 | 35 | 2.6 | |
200×200 | 10 | 35 | 3.52 | |
200×200 | 12 | 35 | 2.94 |
Ipleyiti yeAnchor | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
E-R32 | 95×95 | 25 | 35 | 1.6 |
120×120 | 30 | 35 | 3.2 | |
150×150 | 8 | 35 | 1.3 | |
200×200 | 10 | 35 | 3.06 |
R38 Self Drilling Ankile
Ibha yeAnchor eHollow | |||||
Ubungakanani | Dia yangaphandle. | I-Dia yangaphakathi. | Umthwalo wokugqibela | Yield Load | Ubunzima |
(mm) | (mm) | (kN) | (kN) | (Kg/m) | |
S-R38/20 | 38 | 20 | 500 | 400 | 5.5 |
E-R38/22 | 38 | 22 | 500 | 400 | 4.95 |
E-R38/18 | 38 | 18 | 550 | 430 | 6 |
C-R38/22.5 | 38 | 22.5 | 500 | 400 | 4.8 |
C-R38/21 | 38 | 21 | 500 | 400 | 5.25 |
I-Drill Bit | |||
Uhlobo | Dia yangaphandle. | Ubunzima | Uluhlu lweSicelo (Iingcebiso) |
(mm) | (Ikg) | ||
Steel cross bit | 76 mm | 1.2 | Isuntswana lesiphambano esiqinileyo ukuze sikhululeke ukuya kwiimeko ezixineneyo ezinamatye amancinci |
90 mm | 1.4 | ||
Steel arched bit | 76 mm | 1.2 | Isuntswana le-arched arched for optimized geometry kumhlaba ongadityaniswanga onamatye amancinci |
TC arched bit | 115 mm | 2.85 | I-TC i-arched bit yejometri ephuculweyo yokwakheka kwamatye athambileyo ukuya aphakathi |
TC umnqamlezo bit | 76 mm | 1.25 | I-TC cross bit yolwakhiwo oluthambileyo ukuya oluphakathi |
90 mm | 1.45 | ||
TC 3 cutter bit | 76 mm | 0.85 | I-TC ifake isuntswana kulwakhiwo oluthambileyo ukuya kweliphakathi |
Steel iqhosha bit | 76 mm | 1 | Intwana yeqhosha eliqinileyo lelitye elingadityaniswanga elinamatye |
bit iqhosha le-TC | 76 mm | 1 | Faka iqhosha le-TC kulwakhiwo oluphakathi lwamatye |
Umlingane | ||||
Ubungakanani | Dia yangaphandle. | Ubude | Ubunzima | Phawula |
(mm) | (mm) | (Kg/pc) | ||
S-R38 | 51 | 180 | 1.33 | Ngesakhiwo sokutywina |
51 | 200 | 1.5 | ||
51 | 220 | 1.67 | ||
E-R38 | 51 | 180 | 1.38 | Ngaphandle kwesakhiwo sokutywina |
51 | 200 | 1.55 | ||
51 | 220 | 1.68 |
Hex Nut | ||||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima | Ukuqina |
(mm) | (mm) | (Kg/pc) | (HRC) | |
S-R38 | 50 | 60 | 1.47 | 25-30 |
Ipleyiti eDomed | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
E-R38 | 150×150 | 8 | 41 | 3.6 |
200×200 | 12 | 41 | 1.38 |
Ipleyiti yeAnchor | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
E-R38 | 140×140 | 35 | 41 | 5 |
150×150 | 25 | 41 | 4.1 | |
200×200 | 12 | 41 | 3.67 |
R51 Self Drilling Ankile
Ibha yeAnchor eHollow | |||||
Ubungakanani | Dia yangaphandle. | I-Dia yangaphakathi. | Umthwalo wokugqibela | Yield Load | Ubunzima |
(mm) | (mm) | (kN) | (kN) | (Kg/m) | |
S-R51/34 | 51 | 34 | 580 | 450 | 6.95 |
S-R51/29 | 51 | 29 | 800 | 630 | 9 |
E-R51/36 | 51 | 36 | 550 | 430 | 6.15 |
E-R51/35 | 51 | 35 | 580 | 450 | 6.4 |
E-R51/31 | 51 | 31 | 800 | 630 | 8.2 |
C-R51/33 | 51 | 33 | 800 | 630 | 8 |
I-Drill Bit | |||
Uhlobo | Dia yangaphandle. | Ubunzima | Uluhlu lweSicelo (Iingcebiso) |
(mm) | (Ikg) | ||
Steel cross bit | 85 mm | 1.3 | Isuntswana lesiphambano esiqinileyo ukuze sikhululeke ukuya kwiimeko ezixineneyo ezinamatye amancinci |
TC umnqamlezo bit | 115 mm | 1.8 | I-TC cross bit yolwakhiwo oluthambileyo ukuya oluphakathi |
Steel iqhosha bit | 100 mm | 1.85 | I-TC faka isuntswana leqhosha lelitye elingadityaniswanga elinamatye |
115 mm | 2 | ||
bit iqhosha le-TC | 100 mm | 1.85 | Faka iqhosha le-TC kulwakhiwo oluphakathi lwamatye |
Umlingane | ||||
Ubungakanani | Dia yangaphandle. | Ubude | Ubunzima | Phawula |
(mm) | (mm) | (Kg/pc) | ||
S-R51 | 63 | 200 | 1.85 | Ngesakhiwo sokutywina |
63 | 220 | 2 | ||
E-R51 | 63 | 200 | 1.84 | Ngaphandle kwesakhiwo sokutywina |
63 | 220 | 2.13 |
Hex Nut | ||||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima | Ukuqina |
(mm) | (mm) | (Kg/pc) | (HRC) | |
S-R51 | 75 | 70 | 1.53 | 25-30 |
75 | 80 | 1.84 |
Ipleyiti eDomed | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
E-R38 | 200×200 | 15 | 55 | 4.7 |
Ipleyiti yeAnchor | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
E-R51 | 150×150 | 40 | 56 | 6.2 |
180×180 | 45 | 56 | 10.5 | |
200×200 | 30 | 60 | 8.72 | |
250×250 | 40 | 60 | 18.9 |
T30 Self Drilling Ankile
Ibha yeAnchor eHollow | |||||
Ubungakanani | Dia yangaphandle. | I-Dia yangaphakathi. | Umthwalo wokugqibela | Yield Load | Ubunzima |
(mm) | (mm) | (kN) | (kN) | (Kg/m) | |
S-T30/16 | 30 | 16 | 220 | 180 | 2.9 |
S-T30/14 | 30 | 14 | 260 | 220 | 3.35 |
S-T30/11 | 30 | 11 | 320 | 260 | 3.6 |
E-T30/14 | 30 | 14 | 320 | 260 | 3.35 |
I-Drill Bit | |||
Uhlobo | Dia yangaphandle. | Ubunzima | Uluhlu lweSicelo (Iingcebiso) |
(mm) | (Ikg) | ||
Umnqamlezo owenziwe lukhuni | 42mm | 0.30kg | Isuntswana lesiphambano esiqinileyo ukuze sikhululeke ukuya kwiimeko ezixineneyo zomhlaba |
46mm | 0.32kg | ||
51mm | 0.40kg | ||
76mm | 0.56kg | ||
TC umnqamlezo bit | 42mm | 0.30kg | I-TC cross bit yolwakhiwo oluthambileyo ukuya oluphakathi |
46mm | 0.32kg | ||
51mm | 0.40kg | ||
Isuntswana leqhosha eliqinileyo | 42mm | 0.30kg | Intwana yeqhosha eliqinileyo lelitye elingadityaniswanga elinamatye |
46mm | 0.32kg | ||
51mm | 0.40kg | ||
bit iqhosha le-TC | 46mm | 0.45kg | Iqhosha le-TC elincinci lolwakhiwo oluphakathi lwamatye |
51mm | 0.69kg |
Umlingane | ||||
Ubungakanani | Dia yangaphandle. | Ubude | Ubunzima | Phawula |
(mm) | (mm) | (Kg/pc) | ||
S-T30 | 38 | 105 | 0.39 | Ngesakhiwo sokutywina |
E-T30 | 38 | 105 | 0.45 | Ngaphandle kwesakhiwo sokutywina |
Hex Nut | ||||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima | Ukuqina |
(mm) | (mm) | (Kg/pc) | (HRC) | |
S-T30 | 46 | 35 | 0.31 | 25-30 |
I-Spherical Collar Nut | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
S-T30 | 46 | 35 | 0.33 | 290-340 |
Ipleyiti yeAnchor | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
S-T30 | 150×150 | 25 | 40 | 4.2 |
200×200 | 8 | 36 | 2.43 |
T40 Self Drilling Ankile
Ibha yeAnchor eHollow | |||||
Ubungakanani | Dia yangaphandle. | I-Dia yangaphakathi. | Umthwalo wokugqibela | Yield Load | Ubunzima |
(mm) | (mm) | (kN) | (kN) | (Kg/m) | |
S-T40/20 | 40 | 20 | 539 | 430 | 6.2 |
S-T40/16 | 40 | 16 | 660 | 525 | 7.2 |
E-T40/22 | 40 | 22 | 539 | 430 | 5.7 |
E-T40/18 | 40 | 18 | 660 | 525 | 6.8 |
I-Drill Bit | |||
Uhlobo | Dia yangaphandle. | Ubunzima | Uluhlu lweSicelo (Iingcebiso) |
(mm) | (Ikg) | ||
Umnqamlezo owenziwe lukhuni | 76mm | 0.90kg | Isuntswana lesiphambano esiqinileyo ukuze sikhululeke ukuya kwiimeko ezixineneyo zomhlaba |
90mm | 1.5kg | ||
100mm | 1.65kg | ||
115mm | 2.6kg | ||
TC umnqamlezo bit | 76mm | 1.2kg | I-TC cross bit yolwakhiwo oluthambileyo ukuya oluphakathi |
90mm | 1.75kg | ||
100mm | 2kg | ||
115mm | 2.8kg | ||
130mm | 3.1kg | ||
150mm | 5kg | ||
Umnqamlezo owenziwe lukhuni | 76mm | 1.15kg | Intwana yeqhosha eliqinileyo lelitye elingadityaniswanga elinamatye |
90mm | 1.68kg | ||
100mm | 2.15kg | ||
115mm | 2.3kg | ||
130mm | 3.15kg | ||
bit iqhosha le-TC | 76mm | 1.78kg | Iqhosha le-TC elincinci lolwakhiwo oluphakathi lwamatye |
90mm | 1.4kg | ||
100mm | 2kg | ||
115mm | 2.8kg | ||
130mm | 4.92kg |
Umlingane | ||||
Ubungakanani | Dia yangaphandle. | Ubude | Ubunzima | Phawula |
(mm) | (mm) | (Kg/pc) | ||
S-T40 | 54 | 140 | 1.09 | Ngesakhiwo sokutywina |
57 | 140 | 1.37 | ||
E-T40 | 54 | 140 | 1.11 | Ngaphandle kwesakhiwo sokutywina |
57 | 140 | 1.39 |
Hex Nut | ||||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima | Ukuqina |
(mm) | (mm) | (Kg/pc) | (HRC) | |
S-T40 | 65 | 50 | 0.92 | 25-30 |
I-Spherical Collar Nut | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
S-T40 | 65 | 50 | 0.86 | 290-340 |
Ipleyiti yeAnchor | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
S-T40 | 115×115 | 20 | 56 | 1.6 |
125×125 | 24 | 56 | 2.4 | |
200×200 | 12 | 56 | 3.28 | |
200×200 | 30 | 56 | 8.5 |
T52 Self Drilling Ankile
Ibha yeAnchor eHollow | |||||
Ubungakanani | Dia yangaphandle. | I-Dia yangaphakathi. | Umthwalo wokugqibela | Yield Load | Ubunzima |
(mm) | (mm) | (kN) | (kN) | (Kg/m) | |
S-T52/24 | 52 | 24 | 929 | 730 | 10.2 |
S-T52/26 | 52 | 26 | 929 | 730 | 9.7 |
Umlingane | ||||
Ubungakanani | Dia yangaphandle. | Ubude | Ubunzima | Phawula |
(mm) | (mm) | (Kg/pc) | ||
S-T52 | 70 | 160 | 2.31 | Ngesakhiwo sokutywina |
E-T52 | 70 | 160 | 2.46 | Ngaphandle kwesakhiwo sokutywina |
Hex Nut | ||||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima | Ukuqina |
(mm) | (mm) | (Kg/pc) | (HRC) | |
S-T52 | 80 | 70 | 1.94 | 25-30 |
I-Spherical Collar Nut | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
S-T52 | 80 | 70 | 2.3 | 290-340 |
Ipleyiti yeAnchor | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
SST52 | 145×145 | 27 | 65 | 3.6 |
200×200 | 30 | 65 | 8.59 | |
220×220 | 35 | 65 | 13.1 |
T76 Self Drilling Anchor
Ibha yeAnchor eHollow | |||||
Ubungakanani | Dia yangaphandle. | I-Dia yangaphakathi. | Umthwalo wokugqibela | Yield Load | Ubunzima |
(mm) | (mm) | (kN) | (kN) | (Kg/m) | |
E-T76/51 | 76 | 51 | 1600 | 1200 | 16.5 |
E-T76/45 | 76 | 45 | 1900 | 1500 | 19.7 |
Umlingane | ||||
Ubungakanani | Dia yangaphandle. | Ubude | Ubunzima | Phawula |
(mm) | (mm) | (Kg/pc) | ||
S-T76 | 95 | 200 | 4.26 | Ngesakhiwo sokutywina |
95 | 220 | 4.8 |
Hex Nut | ||||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima | Ukuqina |
(mm) | (mm) | (Kg/pc) | (HRC) | |
S-T76 | 100 | 75 | 2.4 | 25-30 |
100 | 80 | 2.67 |
I-Spherical Collar Nut | |||
Ubungakanani | Ubungakanani obungundoqo | Ubude | Ubunzima |
(mm) | (mm) | (Kg/pc) | |
E-T76 | 95 | 70 | 1.9 |
Ipleyiti yeAnchor | ||||
Ubungakanani | Imilinganiselo | Ukutyeba | Umngxuma Dia. | Ubunzima |
(mm) | (mm) | (mm) | (Kg/pc) | |
S-T76 | 250×250 | 60 | 80 | 27 |
250×250 | 40 | 80 | 18 |